This is a continuation of a long topic, addressed by post number rather than by page. Start at post 1.
Worth separating two things that post #87 runs together.
Practical note that does not fit anywhere else. Whatever you conclude from this topic, write down what you did and when. The single most useful thing in your own records is not any individual result; it is that they are dated and consecutive.
Insulin syringe graduations: U-100 syringes are marked in units where 100 units = 1 mL. Always confirm your syringe is U-100. Confusion between insulin units and milligrams is the most common syringe error.
Sharps disposal: needles and syringes should be disposed in a sharps container (a rigid, puncture-resistant container). Do not put them in regular trash. Many pharmacies accept filled sharps containers.
Needle gauge: smaller numbers (30G) are finer and less painful. Larger numbers (25G) are courser. For subcutaneous injection, 27-30G is typical. Finer needles take longer to draw up but hurt less.
Aspirating before injection: for subcutaneous injection, aspirating (pulling back on the plunger to check for blood) is not necessary and is sometimes discouraged because it is associated with more discomfort. Subcutaneous injection without aspiration is standard practice.
Picking up post #95: that is the part I would want checked first.
Syringe barrel size: common sizes are 0.3 mL, 0.5 mL, and 1.0 mL. Smaller barrels are more legible for small doses. Larger barrels hold larger volumes. Choose based on your dose.
Aspirating before injection: for subcutaneous injection, aspirating (pulling back on the plunger to check for blood) is not necessary and is sometimes discouraged because it is associated with more discomfort. Subcutaneous injection without aspiration is standard practice.
Needle gauge: smaller numbers (30G) are finer and less painful. Larger numbers (25G) are courser. For subcutaneous injection, 27-30G is typical. Finer needles take longer to draw up but hurt less.
post #103 is right about the mechanism and I think understates the practical bit.
Dead volume: residual liquid in the hub and needle after withdrawal. Typical residual is 0.01 to 0.02 mL for an insulin syringe with a fixed needle. Accounting for it matters if precision matters.
Needle length: typical lengths for subcutaneous injection are 4-6 mm (short), 8 mm (standard), or 10-12 mm (longer). Longer needles are needed for deeper tissue or if you have abdominal adiposity.
On post #103 — agreed on the reasoning, with one qualification.
Practical note that does not fit anywhere else. Whatever you conclude from this topic, write down what you did and when. The single most useful thing in your own records is not any individual result; it is that they are dated and consecutive.
post #107 answers the question as asked. The question underneath it is different.
Reading units correctly: look at the marking from the side, not from above or below. The bottom of the plunger tip is the reading. Parallax error (wrong angle) is a source of dosing error.
This follows post #107 rather than contradicting it.
Sharps disposal: needles and syringes should be disposed in a sharps container (a rigid, puncture-resistant container). Do not put them in regular trash. Many pharmacies accept filled sharps containers.
For anyone arriving from a search: the marked solution above is the direct answer, and the replies underneath it add the caveats that make it safe to use.
Needle length: typical lengths for subcutaneous injection are 4-6 mm (short), 8 mm (standard), or 10-12 mm (longer). Longer needles are needed for deeper tissue or if you have abdominal adiposity.
Coming back to post #112, because the follow-up matters more than the original answer.
Dead volume: residual liquid in the hub and needle after withdrawal. Typical residual is 0.01 to 0.02 mL for an insulin syringe with a fixed needle. Accounting for it matters if precision matters.
Insulin syringe graduations: U-100 syringes are marked in units where 100 units = 1 mL. Always confirm your syringe is U-100. Confusion between insulin units and milligrams is the most common syringe error.
Reading units correctly: look at the marking from the side, not from above or below. The bottom of the plunger tip is the reading. Parallax error (wrong angle) is a source of dosing error.
I read post #116 twice before replying, because I had assumed the opposite.
Aspirating before injection: for subcutaneous injection, aspirating (pulling back on the plunger to check for blood) is not necessary and is sometimes discouraged because it is associated with more discomfort. Subcutaneous injection without aspiration is standard practice.
post #118 answers the question as asked. The question underneath it is different.
Fixed versus detachable needles: insulin syringes usually have fixed needles (no dead volume loss to the hub). Luer-lock syringes use detachable needles (more dead volume). Fixed needles are preferred for small doses.
Needle gauge: smaller numbers (30G) are finer and less painful. Larger numbers (25G) are courser. For subcutaneous injection, 27-30G is typical. Finer needles take longer to draw up but hurt less.